How to use ADB tool commend to get a vSignage player screenshot?

Download ADB from https://developer.android.com/studio/command-line/adb.html 1. Run cmd commend and go to the adb save folder that connect to device via Adb over TCP, if use Adb wire, skip this step     adb connect {ip} for example:  adb connect 192.168.2.112 2. Take screenshot and save to device     adb shell screencap -p /sdcard/...

The image is distorted from NMP-302w HDMI out, how can I do?

You can refer below steps to check the issue. 1. To reset the NMP-302w. 2. To replace the HDMI(extension) cable. If above steps can't solve the issue, it will be NMP-302w mainboard issue, you need to replace NMP-302w.

Does NMP-302w and NMP580-W support touch content?

NMP-302w and NMP580-W support EP5520T touch function, you can use these two models with EP5520T, then you will have touch function.

How to prevent image quality loss when exporting from Signage Manager?

While editing content with Signage Manager, it will compress and save photo in lower quality. Please follow below procedures to replace the photo. 1. After finishing editing in Signage Manager, choosing “Export to USB”. 2. Open “File Explorer” and locate USB drive in SMIL/media folder. 3. Copy original photos to this folder and...

How to get back to the dashboard while content is playing via vSignage?

There are two methods to get back to the dashboard. 1. Press up button on the remote control to go to the dashboard 2. Connected to a mouse, directly press and hold anyone of the corner area, after successfully triggering the countdown, the corner area will flash in reverse (as shown in the figure). It will exit after ten seconds. 

Does the EP5520 support WPA2-Enterprise authentication and certificate installation?

Yes. The capability for Enterprise authentication depends on the hardware specifications of the installed Wi-Fi module/dongle and its firmware compatibility. Instructions & Steps: Hardware Verification: Supported Wi-Fi security protocols are dictated by the Wi-Fi Module/Dongle. Please ensure your module supports 802.1X / WPA2-Enterprise ...

ViewSonic CDE30 Series Power Save Modes: Which Mode Should I Use?

ViewSonic CDE30 Series power save modes: Which mode should i use? There are four Power Save modes to choose from and knowing which one to use depends on the application. For this scenario we will cover digital signage, information and monitoring systems and meeting rooms where always-on, wake up on active signal and fast boot time is a must...

What USB WiFi dongle/adapter will work with commercial displays, the CDM, CDE, EP series?

Model Name CDM series CDE10 series CDE20 series EP5540/T EP5542/T Supported WiFi Dongle Built-in WiFi module LB-WiFi-001 LB-WiFi-001 TL-WN725N TL-WN725N TL-WN725N TL-WN725N VSB050 VSB050 VB-WIFI-001 Note: 1. WPA stands for Wi-Fi Protected Access.  2. All WiFi modules and dongles only support W...

How to Disable the Android System on the CDE20 Series.

1. On the Remote Control press INPUT 9 9 1 to enter factory mode. 2. Select Other Setting in the DEBUG MENU. 3. Select Boot Mode. 4. A dialog box will pop up. Select – Disable Embedded OS. 5. Press OK on the Remote Control and the system will reboot. 

How to upgrade the firmware on Stand type EPoster, EP5520/EP5520T, EP5540/EP5540T, EP5542/EP5542T?

1. Format the USB disk as FAT32. 2. Unzip the “MstarUpgrade_848.zip” and then copy the .bin file to the USB disk (FAT32) in the root directory. 3. In Android mode, press the Source menu button, then press INPUT 9 9 1 to open the Service Menu. 4. Select "Firmware Update" and press OK.  5. Select "Upgrade Main" and press OK. ...