Skip to main content

Why can’t I run ViewSplit when connected to ViewSonic monitor?

Your ViewSonic monitor must be set to the Main display. To verify this please follow the steps below:     1. Right click on your desktop and select “Display Settings”.      2. Click on the display number at the top that you want to make the main display and check the “Make this my main display box” under Multiple displays.    3. If th...

Why Your Monitor Mount Joint Might Be Stiff

The rotation axis of the Arm Hinge may feel tight or exhibit restricted movement. This is by design, as the axis incorporates a degree of resistance to help prevent the monitor from dropping, tilting, or moving unintentionally after installation. Before a monitor is installed or when the monitor’s weight is not applied, the rotation...

Which cable do I need to support a 144Hz refresh rate?

To achieve 144Hz, you must use the correct version of DisplayPort (DP) or HDMI based on your resolution. DP is the recommended interface for high refresh rates. Cable Requirement Table: Target Resolution Recommended Cable (or higher) Note 1080p (FHD) DisplayPort / HDMI 1.3 Supported by most modern cables 1440p (2K) DisplayPort 1.2 /...

How to restore the monitor to factory default settings?

Use the "Memory Recall" or "All Reset" option within the monitor's OSD menu to revert all adjustments to their original state. Open the OSD Main Menu: Front Buttons: Press the button labeled [1] or [Menu]. Rear/Side Buttons: Press the designated menu button (refer to the icons on the bezel). Joystick Control: Press the center of...

What should I do if vertical or horizontal lines appear on my monitor?

Identify whether it is a "Hardware Failure" or a "Signal Issue." The quickest way is to open the monitor's OSD menu to isolate the cause. Perform the OSD Test (Crucial): Press the monitor buttons to bring up the built-in menu. Lines appear OVER the menu: This indicates a hardware/panel failure. Proceed to step 5. Lines are NOT on t...

What to do when the screen image is pixelated or blurry?

Blurry images are typically caused by an incorrect resolution or scaling setting. Ensure your computer is set to the monitor's Native Resolution. Troubleshooting Steps: Set to Native Resolution: Windows: Right-click desktop > [Display settings] > [Display resolution]. Choose the one labeled (Recommended). macOS: Go to [System Sett...

Why is the "Auto Image Adjust" function grayed out in the OSD menu?

This is a feature, not a bug. When using a digital connection (HDMI, DisplayPort, or USB-C), the monitor automatically locks onto the signal with pixel-perfect precision, rendering manual adjustments unnecessary. Detailed Explanation: Digital vs. Analog Signals: * Analog (VGA): These signals may require "Auto Image Adjust" to correct ima...

How to setup and configure dual monitors?

Connect your cables, then use system shortcuts to choose between "Extend" or "Duplicate" modes and arrange the display order. Step-by-Step Instructions: 1. Fast Mode Switching (Windows) Press the Win + P shortcut. Select [Extend] to use both screens for different content (Recommended). Select [Duplicate] to show the same image on b...

Why can’t my monitor automatically detect a source?

The "Auto Detect" feature is disabled by default on many models. You must manually enable it within the OSD menu to allow the monitor to switch between active ports automatically. Step-by-Step Instructions: Press the physical button to call up the OSD Main Menu. Navigate to the [Input Select] section. Locate [Auto Detect] at the bo...

Why does my TD2220 randomly receive touch signal and respond accordingly while exposed to sunlight?

TD2220 is an optical touch monitor which uses two CMOS cameras (optical sensors) placed in the corners at the top of the screen as well as three reflectors (light strips). These cameras are used to look across the entire touch surface for touch events. When an object touches the screen, it blocks some of the light being received by the sensor...

LED Monitor Support

General Questions ColorPro™ (VP series)

General InquiriesContact Us

Contact Us directly if you’re unable to get the answers and solutions for your ViewSonic products.