How to use ADB tool commend to get a vSignage player screenshot?

Download ADB from https://developer.android.com/studio/command-line/adb.html 1. Run cmd commend and go to the adb save folder that connect to device via Adb over TCP, if use Adb wire, skip this step     adb connect {ip} for example:  adb connect 192.168.2.112 2. Take screenshot and save to device     adb shell screencap -p /sdcard/...

How to set up video wall in daisy chain?

Here’re major steps to set up video wall in portrait position for your reference. 1. Set up  monitor ID in OSD menu as 1~4 prior to mounting monitors.   2. Connect  IR sensor cable to monitor 1.   3. Connect  the PC to monitor 1 with DP cable firstly for easy setup & adjustment  afterwards.   4. Mounting  monitor 1/2/3/4 in portrait p...

The image is distorted from NMP-302w HDMI out, how can I do?

You can refer below steps to check the issue. 1. To reset the NMP-302w. 2. To replace the HDMI(extension) cable. If above steps can't solve the issue, it will be NMP-302w mainboard issue, you need to replace NMP-302w.

How to check whether vSignage can sync with others players and see the campaign?

If you are unable to sync the contents, there may be a connection issue.    To verify if the admin is sync with the player, there is a JSON API in vSignage. 1. First make sure your windows firewall setting has allow vSigange to access. 2. Please use this API to check if source player see any other players and campaign. Open the Chrome br...

Which network ports should be opened for Signage Manager and media players?

 To ensure Signage Manager can discover and control players over a Local Area Network (LAN), please ensure that TCP 80, 8080, 443, and UDP 1900 are opened in your firewall settings. Port Configuration Table: Port TCP UDP Description 80 TCP Hypertext Transfer Protocol (HTTP), main communication port with legacy play...

How to prevent image quality loss when exporting from Signage Manager?

While editing content with Signage Manager, it will compress and save photo in lower quality. Please follow below procedures to replace the photo. 1. After finishing editing in Signage Manager, choosing “Export to USB”. 2. Open “File Explorer” and locate USB drive in SMIL/media folder. 3. Copy original photos to this folder and...

How to get back to the dashboard while content is playing via vSignage?

There are two methods to get back to the dashboard. 1. Press up button on the remote control to go to the dashboard 2. Connected to a mouse, directly press and hold anyone of the corner area, after successfully triggering the countdown, the corner area will flash in reverse (as shown in the figure). It will exit after ten seconds. 

Does the EP5520 support WPA2-Enterprise authentication and certificate installation?

Yes. The capability for Enterprise authentication depends on the hardware specifications of the installed Wi-Fi module/dongle and its firmware compatibility. Instructions & Steps: Hardware Verification: Supported Wi-Fi security protocols are dictated by the Wi-Fi Module/Dongle. Please ensure your module supports 802.1X / WPA2-Enterprise ...

ViewSonic CDE30 Series Power Save Modes: Which Mode Should I Use?

ViewSonic CDE30 Series power save modes: Which mode should i use? There are four Power Save modes to choose from and knowing which one to use depends on the application. For this scenario we will cover digital signage, information and monitoring systems and meeting rooms where always-on, wake up on active signal and fast boot time is a must...

What USB WiFi dongle/adapter will work with commercial displays, the CDM, CDE, EP series?

Model Name CDM series CDE10 series CDE20 series EP5540/T EP5542/T Supported WiFi Dongle Built-in WiFi module LB-WiFi-001 LB-WiFi-001 TL-WN725N TL-WN725N TL-WN725N TL-WN725N VSB050 VSB050 VB-WIFI-001 Note: 1. WPA stands for Wi-Fi Protected Access.  2. All WiFi modules and dongles only support W...