Ugrás a fő tartalomra

How to enable the input source auto detect function?

Please open the OSD menu and navigate into “Input Select”. Then, select Auto-Detect and make sure it is set to ON.

Do the VP2468’s USB ports support Apple device power charging?

The 4 USB ports support 5V 900mA Apple device power charging. The fourth downstream USB port can support device charging while the display is on “standby mode”, but all other ports will only charge devices while the display is “on”. As of Dec. 11 2020, VP models support standby model with charging function via 2.1A USB port of monito...

Why can’t my monitor automatically detect a source?

The "Auto Detect" feature is disabled by default on many models. You must manually enable it within the OSD menu to allow the monitor to switch between active ports automatically. Step-by-Step Instructions: Press the physical button to call up the OSD Main Menu. Navigate to the [Input Select] section. Locate [Auto Detect] at the bo...

Why didn't my Windows desktop automatically rotate to fit the orientation of the monitor when the Auto-Pivot function is enabled on my Windows OS?

For optimal performance, please make sure your monitor is fully up to date. If your VP2468 monitor’s firmware version is M001 or M002, please make sure your OSD Pivot and Auto-Pivot functions are, both, set to Auto.

What ViewSonic monitors can support Auto Pivot function?

As of Dec. 8 2020, below VP models support Auto Pivot function.   VP2458, VP2468, VP2468a, VP2768, VP2768a, VP2785-4K VP2768-4K, VP2785-2K, VP2771, VP2775, VP3268-4K.   Please refer to below steps to enable the function.   1.Download and install vDisplay Manager. 2.Follow UG for connection and setting. 3.Enable DDC/CI in monitor OSD to...

How to check the monitor’s current firmware version?

There are 2 ways:   1.On Monitor, please navigate to OSD -> Setup Menu -> Information, where you will see your current firmware version.   **For VP2468 versions M001 and M002, this function is not supported. If the firmware version is not present in the Information page, please update to version M010 or later.     2. On PC/Laptop, you ...

Why doesn't the OSD menu auto-rotate to match the monitor's orientation?

The [Auto Pivot] feature for the OSD menu must be manually enabled in the monitor's settings or synced via the vDisplay Manager software. Step-by-Step Instructions: Open OSD: Press the monitor buttons to bring up the [Main Menu]. Navigate to Setup: Go to the [Setup Menu] tab. Enable Auto Pivot: Locate the [Auto Pivot] setting and t...

Minor image retention may occur when a static image is displayed on the screen for extended periods of time.

This is a normal occurrence for In-Plane Switching (IPS) monitor panels. The longer an image is left static on the screen, the more noticeable image retention will be.  In order to prevent image retention, enable the screen saver function on your monitor so that images are not static on your screen for extended periods of time.

Why isn’t the monitor displaying anything after I plug in my DisplayPort input?

Please make sure to connect PC to the DisplayPort input instead of the DisplayPort output port on the monitor.    If your graphic card is capable of DisplayPort 1.1, please follow these steps and adjust monitor setting:   “Menu >> Setup Menu >> DisplayPort 1.2 Off”.

Why is my monitor not detected by the Firmware Update Tool?

Please make sure to use “FW_Update_Tool_v1.08”. Please follow the step by step instructions below to resolve the problem. When the program is initialized, the error message shown below will appear. A Windows error message might also pop up few seconds later. Please close the program and the error messages, then follow the in...

LED Monitor Támogatás

General Questions ColorPro™ (VP series)

Általános kérdésekKapcsolatfelvétel

Kérjük, forduljon közvetlenül hozzánk, ha nem talál válaszokat és megoldásokat a ViewSonic termékeivel kapcsolatban.