Ugrás a fő tartalomra

How do I connect external speaker(s) to my projector?

1.Wired connection:   1.1 via 3.5mm audio out:       If the projector is equipped with a 3.5 mm audio out mini jack, usually it is  green and marked as          Audio Out. Please connect a 3.5 mm audio cable between speaker and projector for audio output        purpose.     1.2 via S/PDIF:        If the model is equipped with S/PDIF por...

How to mirror iPhone or iPad screen to the projector? (Wired Connection Guide)

Use a USB-C cable or an appropriate HDMI adapter for a stable, low-latency wired connection. USB-C Direct Connection (Recommended): Use a USB-C cable that supports video transmission (using the cable provided with the projector is highly recommended). Connect your device directly to the projector's [USB-C] port. Select [USB-C] a...

Why is there a high-pitched noise or buzzing from my projector?

Slight humming is often normal for 4K models due to XPR technology. For other noises, check fan settings and power stability. Identify Normal XPR Noise (4K Models): 4K UHD projectors use XPR pixel-shifting technology, which produces a subtle high-pitched hum during operation. This is normal and not a defect. Adjust Fan Settings: Go to ...

How to fix shadows, ghosting, or double images on the projector screen?

Image artifacts are often caused by poor cable quality or signal interference. Use high-quality cables and avoid using excessive adapters. Use Bundled Cables: Test using the [original video cable] provided with the product. Remove Intermediate Devices: Disconnect any [docking stations], [adapters], or [video splitters]. Connect the ...

There is a pixel stuck on or off

Stuck or twinkling pixels on the projected image may be due to a defective DMD chip. These pixels can show up as bright, dark or twinkling points. They look similar to pixel defects on LCD displays. This cannot be fixed by the end user and must be sent in for service. Contact ViewSonic Customer Care to verify if your unit qualifies for warrant...

Why Can't I Power Off the Projector via its Remote Control?

For Models: PA/PG/PX Series “Power On” and “Power Off” are separated as two (2) different buttons on the remote control. This is different from the PJD series.

What to do if I can't mirror my screen after I updated the iOS version to iOS14?

Due to iOS14 compatibility issues, please follow below table for solution.   Model Solution X100-4K Install EAirPlay.apk and follow instruction X10-4K Update FW to V1.13 via OTA M2 Update FW to V1.0 via OTA M1+_G2/M1+_V Update FW to V1.04 via OTA M1 mini plus Update FW to V1.02 via OTA SOP URL: https://support.viewsonic.com/hel...

How to enable the remote controller PgUp and PgDn functions?

In order to enable the PgUp and PgDn function on your remote controller for the PX701-4K projector, please follow the instruction below: Besides your video cable (HDMI), please connect an additional USB cable from the back of the PX701-4K projector to your PC/Laptop. Change the control method to USB by entering your OSD menu -> System ...

How to solve a flickering image on the projector?

Image flickering is mostly caused by loose cables or the Eco Mode settings. Follow these quick steps to resolve it. Secure Physical Connections: Unplug and re-plug the HDMI / VGA cable. Ensure the connection is firm. Try a different cable to rule out internal wire damage. Change Lamp Mode (Top Solution): Go to [Settings]...

How to change the projector image orientation

Use the "Projector Position" setting in the menu to flip or mirror the image according to your installation. Open Menu: Press the [Menu] button on your remote. Navigation: Go to [System Setting: Basic] > [Projector Position]. Choose Your Setup: Front Table: Default setup; projector on a table facing the screen. Ceiling: [Most...

Projector Támogatás

General Questions Technical Documents vRemote Tips & Tricks

Általános kérdésekKapcsolatfelvétel

Kérjük, forduljon közvetlenül hozzánk, ha nem talál válaszokat és megoldásokat a ViewSonic termékeivel kapcsolatban.