Skip to main content

How to set power lock and menu lock?

On some monitors, there is a power button lock that locks the power and power button in the ON position.  There is also a menu lock feature which can lock and unlock the OSD (On-Screen Display) Menu.  Power Lock: To lock the Power Button press and hold both the [1] button and the down arrow button for 10 seconds.  OSD Lock: ...

How to restore the monitor to factory default settings?

Use the "Memory Recall" or "All Reset" option within the monitor's OSD menu to revert all adjustments to their original state. Open the OSD Main Menu: Front Buttons: Press the button labeled [1] or [Menu]. Rear/Side Buttons: Press the designated menu button (refer to the icons on the bezel). Joystick Control: Press the center of...

How to fix ghosting, shadowing, or double images on the screen?

Image artifacts are typically caused by signal degradation or interference. Bypass any docking stations and use high-quality certified cables. Bypass Adapters/Docks: Remove any [Docking Stations] or [Video Splitters]. Connect the monitor directly to your PC to test the image quality. Upgrade Cable Quality: For long-distance connections...

What to do if there is flickering image with my monitor?

Check the monitor: Please do memory recall. Please refer to this FAQ Check device setting: Please check and set to recommended refresh rate.  You can refer to this video. https://www.youtube.com/watch?v=sAkbjPiLNcE   If possible, please connect monitor to another device with different input.   If above doesn’t help, please contact ViewSo...

How to solve the overscan problem with my monitor?

If the image does not fill the screen of the monitor or if it looks like the image is slightly too big for the monitor, try below suggestion.   1.Adjust setting on the PC/laptop:   (1)Set native resolution of monitor in your PC/laptop's Display settings.   (2)Change Scaling in Display settings.   Use the graphic card software to change ...

Why Your Monitor Mount Joint Might Be Stiff

The rotation axis of the Arm Hinge may feel tight or exhibit restricted movement. This is by design, as the axis incorporates a degree of resistance to help prevent the monitor from dropping, tilting, or moving unintentionally after installation. Before a monitor is installed or when the monitor’s weight is not applied, the rotation...

Which cable do I need to support a 144Hz refresh rate?

To achieve 144Hz, you must use the correct version of DisplayPort (DP) or HDMI based on your resolution. DP is the recommended interface for high refresh rates. Cable Requirement Table: Target Resolution Recommended Cable (or higher) Note 1080p (FHD) DisplayPort / HDMI 1.3 Supported by most modern cables 1440p (2K) DisplayPort 1.2 /...

What should I do if vertical or horizontal lines appear on my monitor?

Identify whether it is a "Hardware Failure" or a "Signal Issue." The quickest way is to open the monitor's OSD menu to isolate the cause. Perform the OSD Test (Crucial): Press the monitor buttons to bring up the built-in menu. Lines appear OVER the menu: This indicates a hardware/panel failure. Proceed to step 5. Lines are NOT on t...

How to setup and configure dual monitors?

Connect your cables, then use system shortcuts to choose between "Extend" or "Duplicate" modes and arrange the display order. Step-by-Step Instructions: 1. Fast Mode Switching (Windows) Press the Win + P shortcut. Select [Extend] to use both screens for different content (Recommended). Select [Duplicate] to show the same image on b...

Why can’t my monitor automatically detect a source?

The "Auto Detect" feature is disabled by default on many models. You must manually enable it within the OSD menu to allow the monitor to switch between active ports automatically. Step-by-Step Instructions: Press the physical button to call up the OSD Main Menu. Navigate to the [Input Select] section. Locate [Auto Detect] at the bo...

LED Monitor Support

General Questions ColorPro™ (VP series)

General InquiriesContact Us

Contact Us directly if you’re unable to get the answers and solutions for your ViewSonic products.