How to Upgrade the M1+ Firmware?

  <Notice> The firmware of M1+ will not be used on M1+_G2/_V or M1+ -2.   1. Go to “Downloads” -> ”Driver & Software” by searching M1+ from ViewSonic website to download “M1+ Firmware Update v2.03”.      2. Unzip the downloaded files and copy the Firmware files, “MstarUpgrade.bin" and "M1+WW.bin” to a FAT32 formatted USB drive.  3. Po...

Why can't the M1 mini Power On or Auto Shutdown after charging?

    1. Using a power bank or a USB power adapter with DC output of 5V/2A is required via the Micro USB port for charging the M1 mini battery.   2. Charge the projector for 2 hours (5V/2A) before using it in battery mode for the first time.   Battery Usage Time Information     NOTE:  When the projector is in use, a 5V/2A power ada...

Why is Smart YouTube app not available on Aptoide app store?

Aptoide store removed Smart YouTube apk from their app store. We recommend you download and install SmartTube apk to play YouTube videos. https://smarttubenext.com/#Download_SmartTubeNext_APK_for_Android_Based_Smart_TVs Applicable models: M1MINI, M2, M2e,M1_G2, M1+_G2, M1MINIPLUS, X10-4k,X100-4K,X1000-4K

What ViewSonic projectors support audio in/out via Bluetooth?

As of April 2021, below is BT support model list.

LS921WU is not recognized nor controlled through the web browser by PJ-link

Applicable models: LS600W, PG707X, PG707W, PG706HD, PG706WU, LS831WU, LS750WU, LS850WU, LS860WU, LS920WU, LS921WU, PX728-4K, PX748-4K Please make sure the below webpage password is set in ViewSonic Network control first due to SB-327 law requirement.   1. Enter the IP address of the projector in the address bar of your browser and press E...

How to do Crestron E-control workaround due to Adobe Flash player not being supported?

Step 1  Download and install a Flash Player. “Download the Flash Player projector” from Adobe: https://www.adobe.com/support/flashplayer/debug_downloads.html Step 2 Input the URL of the Crestron interface in the Flash Player: http://[projector.ip]/CrestronUI.swf Where [projector.ip] is the ViewSonic projector’s IP address.

Why a black border on the top/bottom or sides of the image from the projector?

Please check below:   1.Plesae refer to the user guide and adjust Aspect ratio with example below.   2. It could be the format of the movie since not all movies are formatted in 16:9. Some are formatted wider than 16:9 which will create black borders on the top and bottom of the screen.

How to download the latest drivers for my projector

Option 1: Download from the ViewSonic Website Go to http://www.viewsonic.com/us/downloads_section/ Enter the Product Name, Product series and model number. Select the driver based on the operating system of your computer. Once the file downloads, double-click to open and start the installation. If you select Save, double-click on the downl...

Why Can't I Power Off the Projector via its Remote Control?

For Models: PA/PG/PX Series “Power On” and “Power Off” are separated as two (2) different buttons on the remote control. This is different from the PJD series.

There is a pixel stuck on or off

Stuck or twinkling pixels on the projected image may be due to a defective DMD chip. These pixels can show up as bright, dark or twinkling points. They look similar to pixel defects on LCD displays. This cannot be fixed by the end user and must be sent in for service. Contact ViewSonic Customer Care to verify if your unit qualifies for warrant...